Regency Horizon HZ40E Скачать руководство пользователя

Страница: 13 / 72

Regency Horizon® HZ40E-10 Gas Fireplace

installation

FRAMING DIMENSIONS

NOTE:

If not purchasing the optional steel stud kit - adhere to the same framing if purchasing steel studs elsewhere. The use of the optional kit is highly

recommended as it was designed speciically for the product to facilitate ease of installation.

Framing
Dimensions

Description

HZ40E

Framing Height

42” (1067mm)

Framing Width

49-7/8" (1266mm)

Framing Depth

Horizontal Vent 21-3/16" (538mm)

Vertical Vent 25-3/16" (640mm)

Vertical rise -terminating horizontal

Minimum Height to Combustibles

43-7/8" (1114mm)

Corner Wall Depth

61" (1549mm)

Corner Facing Wall Width

86-1/4" (2191mm)

Vent Centerline Height

36 - 1/4" (921mm)

Non-combustible facing height

17” (432mm)

Gas Connection Opening Height

2" (51mm)

Gas Connection Height

4 - 3/16" (106mm)

Gas Connection Inset

8 - 5/16" (211mm)

Gas Connection Opening Width

3 - 1/2" (89mm)

Framing depth measurement is noted with the nailing strips set as far forward on the irebox as possible.

The nailing strips can be adjusted back up to 3-1/4” to allow for varying thicknesses in non-combustible

material & wall inishes.

Non-Combustible

Facing

Metal Stud (Header)

Metal Studs

on edge

Flex or Rigid Pipe

Finished Floor

Drywall or

other facing

Note:

All other framing

around the perimeter may

be of wood construction.

Note:

Three horizontal

steel studs must be installed

after the unit is in position

and the venting, gas, and

electrical is installed. The

horizontal studs allow the

non-combustible wall board

to be attached and

supported.

Содержание Horizon HZ40E









































































Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды

Regency Horizon HZ40E, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды