RADEMACHER RolloSystems T2 Скачать руководство пользователя страница 34

Страница: 34 / 48

Setting the function of control inputs A

and B

The function of each control input can be set as needed. This is done in menus and .

The following functions can be set:

Setting

Function

= Off (factory setting)
= NC mode (potential-free opener contact)
= NO mode (potential-free closer contact)
= Pause mode
= Open (dead-man operation, e.g. for roller shutter switches)*
= Close (dead-man operation, e.g. for roller shutter switches)*

* only potential-free closer contacts for a roller shutter switch

Brief description of functions

= Off

The control input is switched off (factory setting). For example, a motion detector can
be switched off if needed, without having to disconnect it.

= NC mode

A potential-free opener contact (external sensor or motion detector) can be connected
to the control input.

= NO mode

A potential-free closer contact (external sensor or motion detector) can be connected
to the control input.

Содержание RolloSystems T2

















































Результаты поиска

Содержание RolloSystems T2

Отзывы:

Похожие инструкции для RolloSystems T2

Бренды по названию

Популярные бренды

RADEMACHER RolloSystems T2, Инструкция по эксплуатации

Результаты поиска

Содержание RolloSystems T2

Отзывы:

Похожие инструкции для RolloSystems T2

Бренды по названию

Популярные бренды