RADEMACHER RolloSystems T2 Скачать руководство пользователя страница 44

Страница: 44 / 48

Error messages

Error messages are indicated by the LED display and a repeated acoustic signal. The LED display
first shows an „ “ and then the number (e.g. ) of the error message in question.

Display

Description of error

The configuration has been modified.

Remedy:

Perform an automatic end point search (see page 23).

The end points are too close together.

Remedy:

Repeat an automatic end point search (see page 23).

◆

The drive is sticking, movement is no longer possible.

◆

The drive or the sensor electronics are defective.

Remedy:

◆

Check the toothed belt.

◆

Servicing required *

Error in the drive electronics.

Remedy:

◆

Servicing required *

Error in the drive electronics.

Remedy:

◆

A reset may help (see page 37), if not

◆

Servicing required *

The internal speed monitoring system has recognised an error.

Remedy:

◆

Repeat automatic end point search (see page 23).

◆

Servicing required * (should error re-occur)

Please contact our Customer Service department
(see page 48).

Содержание RolloSystems T2

















































Результаты поиска

Содержание RolloSystems T2

Отзывы:

Похожие инструкции для RolloSystems T2

Бренды по названию

Популярные бренды

RADEMACHER RolloSystems T2, Инструкция по эксплуатации

Результаты поиска

Содержание RolloSystems T2

Отзывы:

Похожие инструкции для RolloSystems T2

Бренды по названию

Популярные бренды