RADEMACHER RolloSystems T2 Скачать руководство пользователя страница 14

Страница: 14 / 48

Brief description of control inputs

and B

Connection of external controls

The drive has two control inputs

and

for connecting various external controls,

such as:

◆

Sensor

◆

Motion detector etc.

◆

Roller shutter switch

Colour assignment of the drive cable for the control inputs

Drive cable

Assignment

white (3)

= control input

yellow (4)

= control input

Setting the function of the control inputs (see page 34)

The function of each control input can be set as needed. This is done in menus and .

The following functions can be set:

◆

Off

◆

NC mode (potential-free opener contact)

◆

NO mode (potential-free closer contact)

◆

Pause mode (potential-free closer contact)

◆

Opening, potential-free closer contact
(dead-man operation, e.g. for roller shutter switches)

◆

Closing, potential-free opener contact
(dead-man operation, e.g. for roller shutter switches)

Permissible voltage for control inputs

Input voltage:

9 V to 24 V

Input resistance:

> 47 k

Ω

IMPORTANT

Control inputs not in use must be connected to GND, brown (1) or grey (2).

Содержание RolloSystems T2

















































Результаты поиска

Содержание RolloSystems T2

Отзывы:

Похожие инструкции для RolloSystems T2

Бренды по названию

Популярные бренды

RADEMACHER RolloSystems T2, Инструкция по эксплуатации

Результаты поиска

Содержание RolloSystems T2

Отзывы:

Похожие инструкции для RolloSystems T2

Бренды по названию

Популярные бренды