Quantum LTO 4, Руководство пользователя

Страница: 273 / 297

ALID_STATE range).
SRV_CMDPROC_CMD_REJECT_SEQUENCER_BUSY_
AND_BUFFER_FULL
613h Servo Command rejected since the sequencer was processing an error
and the polled buff
SRV_CANNOT_INSERT_INTO_LPOS_NOTIFY_TABLE_
UNTIL_SCR_AND_WP_FOUND_LP1 614h Servo LPOS values in the notification table are dependent on CM_LP1
and WP_LP1.
SRV_LPOS_ROLLOVER_DETECTED_FROM_CM_PHY
S_LP1 615h Servo Calc phy LP7 from CM phys LP1 is greater then LTO spec
SRV_LPOS_ROLLOVER_DETECTED_FROM_WP_CAL
C_PHYS_LP1 616h Servo Calc phy LP7 from WP calc phys LP1 is greater then LTO spec
SRV_LPOS_TOP_SERVO_AND_BOTTOM_SERVO_CA
LC_LP1_NOT_WITHIN_TOLERANCE 617h Servo The LP1 value calc for top servo didn't match the LP1 value calc
for the bottom
SRV_REEL_MOT_PWR_FAIL_DETECTED 618h Servo 12 volt power reset detected
SRV_REEL_MOT_EXCESSIVE_CURRENT_DEMAND_D
ETECTED 619h Servo Excessive current detected on motor
SRV_FINDZERO_TIME_OUT 61Ah Servo Time out occured waiting for servo response
SRV_FINDZERO_STATE_VARIABLE_OUT_OF_RANGE 61Bh Servo Find zero wrap state variable out of range.
SRV_FINDZERO_COARSE_OR_APPROACHING 61Ch Servo Find zero wrap coarse or approaching api rejected call.
SRV_FINDZERO_INDEX_SETUP_API_REJECT 61Dh Servo Find zero wrap index setup api rejected call.
SRV_FINDZERO_INDEX_HOME_API_REJECT 61Eh Servo Find zero wrap index home api rejected call.
SRV_FINDZERO_HOME_DRIVE_REEL_API_REJECT 61Fh Servo Find zero wrap home drive reel api rejected call.
SRV_FINDZERO_APPROACHING_API_REJECT 620h Servo Find zero wrap approaching zero api rejected call.
SRV_FINDZERO_TOO_MANY_RETRIES_AFTER_COA
RSE_MOTION 621h Servo Find zero wrap coarse exceeded coarse motion retries.
SRV_FINDZERO_TOO_MANY_RETRIES_AFTER_COM
PLETE 622h Servo Find zero wrap retries exceeded after completion.
SRV_CMDPROC_FIND_INDEX_FAILED_WRITING_TO_
LINEAR_COUNTER_API_BUSY 623h Servo Reset linear counter to remember the aligned slot position
SRV_CMDPROC_LINEAR_COUNTER_NOT_RECORDE
D_PREVIOUSLY 624h Servo Linear counter not reset with RECORD ALIGNED SLOT
command prior to this command
SRV_SEQ_POWER_ON_INIT_FAILED_WRITING_TO_LI
NEAR_COUNTER_API_BUSY 625h Servo Reset linear counter failed during power on recovery
SRV_CMDPROC_INVALID_STATE_FOR_RAMP_HEAD
_COMMAND 626h Servo Ramp head command rejected
SRV_CMDPROC_TAPE_NOT_MOVING_FOR_RAMP_H
EAD_COMMAND 627h Servo Ramp head command rejected
SRV_CMD_INVALID_HEAD_POSITION_SPECIFIED_IN
_CHANGE_TRACKING_MODE 628h Servo Head position not a valid tracking head position
SRV_CMD_INVALID_HEAD_POSITION_SPECIFIED_IN
_WRAP_RESTART_TRACKING 629h Servo Head position not a valid tracking head position for restart
tracking
SRV_MOVETAPE_SET_LC_NOTIFICATION_FAILED 62Ah Servo Attempt to set linear counter mark failed since already past
point.
SRV_CMDPROC_REJ_TAPE_NOT_READY 62Bh Servo Tape ready for retension
SRV_STEP_HEAD_EXPECTING_MOVING_UP_WITH_A
DDED_HYSTERESIS_AFTER_REFERENCE_SENSOR_
HIGH 62Ch Servo Expecting moving up with added hysteresis after reference
sensor high.
SRV_CMD_INVALID_COMMAND_CALLED_SEQUENC
E_IS_NULL 62Dh Servo Invalid command called or invalid message sent to sequencer
SRV_TIMEOUT_DURING_HEAD_STEPPER_STOPPING
_AFTER_SEARCHING_FOR_SERVO_BAND 62Eh Servo Timeout during head stepper stopping after searching for servo
bundle
SRV_TIMEOUT_DURING_HEAD_STEPPER_MOVING_
UP_WITH_ADDED_HYSTERESIS_AFTER_REFERENC
E_SENSOR_HIGH 62Fh Servo Timeout during head stepper moving up with added hysteresis
after reference sens
SRV_STEP_HEAD_EXPECTING_SEARCHING_FOR_SE
RVO_BAND 630h Servo Expecting searching for servo bundle
SRV_STEP_HEAD_EXPECTING_HYSTERESIS_BEFOR
E_SEARCHING_FOR_SERVO_BAND_IN_OTHER_DIRE
CTION 631h Servo Expecting hysteresis before searching for servo bundle in other
direction
SRV_STEP_HEAD_EXPECTING_SEARCHING_FOR_SE
RVO_BAND_IN_OTHER_DIRECTION 632h Servo Expecting searching for servo bundle in other direction
SRV_STEP_HEAD_EXPECTING_STOPPING_AFTER_F
AILING_SEARCH_FOR_SERVO_BAND_IN_OTHER_DI 633h Servo Expecting stopping after failing search for servo bundle in other
direction