Pyro-Chem Kitchen Knight II Скачать руководство пользователя

Страница: 19 / 86

SECTION 2 – COMPONENTS

UL EX3830 ULC EX3830

2014-NOV-10 REV. 06 PagE 2-7

KITCHEN KNIGHT II Restaurant Fire Suppression Manual

MODEL RPS-M – REMOTE MECHANICAL PuLL STATION

Remote manual control for the Model MCH3, NMCH3, or

ECH3 control head is provided by the Model RPS-M Remote

Mechanical Pull Station (Part No. 551074). It is connected to

the system control head by stainless steel cable. This cable is

enclosed in 1/2 in. EMT conduit with corner pulleys or flexible

conduit with bends and/or corner pulleys at each change in

direction. The remote mechanical pull station shall be located at

the point of egress. See Figure 2-17.

FIguRE 2-17

002852PC

“QuIK-SEAL” ADAPTOR

The “Quik-Seal” adaptor is a listed mechanical bulkhead fitting

that produces a liquid-tight seal around both distribution piping

and detection conduit which runs through restaurant hoods

and ducts. The “Quik-Seal” adaptor accepts threaded pipe or

conduit. The adaptor is available for 3/8 in. and 1/2 in. pipe or

conduit sizes. When using with EMT conduit, a conduit connec-

tor must be installed in each end of the adaptor. The “Quik-Seal”

adaptor Shipping assembly can be ordered in single or package

of 24. See Figure 2-18.

Shipping

assembly

Hole Size

Size

Part No.

Qty.

Required

3/8 in.

550857

1 1/8 in.

1/2 in.

550859

1 1/8 in.

3/8 in.

550858

1 1/8 in.

1/2 in.

550860

1 1/8 in.

aDaPTOR BODY
gaSKET

LOCKWaSHER

NUT

FIguRE 2-18

000154

“COMPRESSION-SEAL” ADAPTOR

This adaptor is a mechanical bulkhead fitting that produces a

liquid-tight seal around pipe and conduit when installing distribu-

tion piping and detection conduit through restaurant hoods and

ducts. The “Compression-Seal” adaptor is a straight-through

design requiring no cutting or threading of conduit or pipe. The

adaptor is available for EMT conduit size of 1/2 in. (Part No.

79152). See Figure 2-19. “Compression-Seal” adaptor Shipping

assembly must be ordered as stated below:
Shipping

assembly

Hole Size

Size

Part No.

Qty.

Required

1/2 in. EMT Conduit

79153

1 1/8 in.

COMPRESSION NUT

aDaPTOR BODY

LOCKWaSHER

gaSKET

NUT

FIguRE 2-19

“HOOD SEAL” ADAPTOR ASSEMBLY

This adaptor is a mechanical bulkhead fitting that produces a

liquid-tight seal around 1/2 in. EMT conduit when installing the

detection line through restaurant hoods and duct. The adaptor

accepts a high temperature pulley elbow and, when used,

correctly positions the elbow or conduit in line with the conduit

adaptor hole in the detector bracket. The “Hood Seal” eliminates

the need for multiple elbows when penetrating the top of a hood

when installing the detection line. “Hood Seal” adaptors are

available in quantities of six as Shipping assembly Part No.

423253. See Figure 2-20.

SEaL

aDaPTOR

BODY

SEaL NUT

WaSHER

PULLEY

ELBOW

(NOT PaRT

OF aSSEMBLY)

USE ONLY PULLEY ELBOW (PaRT NO. 423250)

gaSKET

000156

FIguRE 2-20

000156

Содержание Kitchen Knight II























































































Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды

Pyro-Chem Kitchen Knight II, Техническое руководство

Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды