Pyro-Chem Kitchen Knight II Скачать руководство пользователя

Страница: 35 / 86

SECTION 3 – SYSTEM DESIGN

UL EX3830 ULC EX3830

2014-NOV-10 REV. 06 PagE 3-9

KITCHEN KNIGHT II Restaurant Fire Suppression Manual

NOZZLE COVERAGE AND PLACEMENT (Continued)
Appliance Protection (Continued)
TABLE 3-4: NOZZLE POSITIONING (Continued)
Range Range

Length - L

width – w

Radius – R

in. (mm)

(711)

(457)

3 1/8

(79)

(711)

(482)

2 7/8

(73)

(711)

(508)

2 5/8

(66)

(711)

(533)

2 1/4

(57)

28 (711)

22 (558)

(50)

(711)

(584)

1 5/8

(41)

(711)

(609)

1 3/8

(34)

28 (711)

25 (635)

(25)

28 (711)

26 (660)

3/4 (19)

28 (711)

27 (685)

3/8

(9)

28 (711)

(0)

4. Small wok

(24 in. (609.6 mm) diameter x 6 in. (152 mm)

depth maximum)

Two nozzles are available for small wok protection: High

proximity and low proximity.

The 1H nozzle (Part No. 551029) is used for high proximity

wok protection. This nozzle is a one flow nozzle. The nozzle

must be located

anywhere on the perimeter

of the appli-

ance, 24 in. to 48 in. (609.6 mm to 1219 mm) above the top

edge of the wok and aimed at the center of the wok. See

Figure 3-14.

The 1L nozzle (Part No. 551026) is used for low proximity

wok protection. This nozzle is a one flow nozzle. The nozzle

must be located

anywhere on the perimeter

of the appli-

ance, 13 in. to 24 in. (331 mm to 609.6 mm) above the top

edge of the wok and aimed at the center of the wok. See

Figure 3-14.

006183PC

1H, 1L

13 IN.

(331 mm)

48 IN.

(1219 mm)

24 IN.

(609.6 mm)

24 IN. (609.6 mm)

DIaMETER MaXIMUM

NOzzLE LOCaTED

ON PERIMETER

FIGuRE 3-14

5. Large wok

(greater than 24 in. to 30 in. (609.6 mm to

762 mm) diameter x 8 in. (203 mm) depth maximum)

Two nozzles are available for large wok protection: High

proximity and low proximity.

The 2H nozzle (Part No. 551028) is used for high proximity

wok protection. This nozzle is a two flow nozzle. The nozzle

must be located

anywhere on the perimeter

of the appli-

ance, 24 in. to 48 in. (609.6 mm to 1219 mm) above the top

edge of the wok and aimed at the center of the wok. See

Figure 3-15.

The 2L nozzle (Part No. 551027) is used for low proximity

wok protection. This nozzle is a two flow nozzle. The nozzle

must be located

anywhere on the perimeter

of the appli-

ance, 13 in. to 24 in. (331 mm to 609.6 mm) above the top

edge of the wok and aimed at the center of the wok. See

Figure 3-15.

006183PC

2H, 2L

13 IN.

(331 mm)

48 IN.

(1219 mm)

24 IN.

(609.6 mm)

30 IN. (762 mm)

DIaMETER MaXIMUM

NOzzLE LOCaTED

ON PERIMETER

FIGuRE 3-15

6. Small Griddle

(1080 in.

(69677 mm

) x 36 in. (914 mm)

longest side maximum)

Two nozzles are available for small griddle protection: High

proximity and low proximity.

The 1H nozzle (Part No. 551029) is used for high proximity

griddle protection. This nozzle is a one flow nozzle. The

nozzle must be located

above any corner

of the hazard

surface, 24 in. to 48 in. (609.6 mm to 1219 mm) above the

cooking surface of the appliance and aimed at a point 12 in.

(304 mm) over and 12 in. (304 mm) in from the corner below

the nozzle. See Figure 3-16.

Содержание Kitchen Knight II























































































Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды

Pyro-Chem Kitchen Knight II, Техническое руководство

Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды