Pyro-Chem Kitchen Knight II Скачать руководство пользователя

Страница: 51 / 86

SECTION 4 – SYSTEM INSTALLATION

UL EX3830 ULC EX3830

2014-NOV-10 REV. 06 PagE 4-1

KITCHEN KNIGHT II Restaurant Fire Suppression Manual

GENERAL

The installation information listed in this section deals with the

limitations and parameters of this pre-engineered system. Those

individuals responsible for the installation of the KITCHEN

KNIgHT II system must be trained and hold a current PYRO-

CHEM certificate in a KITCHEN KNIgHT II training program.
Pipe and fittings for the discharge piping, conduit (EMT),

pipe straps, pipe hangers, mounting bolts, and other

miscellaneous equipment are not furnished as part of the

PYRO-CHEM KITCHEN KNIgHT II Restaurant Fire Suppression

System. These items must be furnished by the installer.
Before attempting any installation, unpack the entire system and

check that all necessary parts are on hand. Inspect parts for

damage. Verify that cylinder pressure is within the acceptable

range as shown on the gauge.

CYLINDER INSTALLATION

The cylinder and valve assembly is shipped with an anti-recoil

plug in the valve discharge port.

CAUTION

The anti-recoil plug must remain in the valve discharge port

until the discharge piping is connected to the valve.

The cylinder must be mounted vertically. The Models PCL-300

and PCL-460 cylinders must be mounted using a Model MB-15

Mounting Bracket Kit. The Model PCL-600 cylinder must be

mounted using a Model MB-1 Mounting Bracket Kit.
The bracket must be securely anchored to the wall using bolts

or lag screws. The wall to which the bracket is attached must

be sufficiently strong to support the cylinder. The bracket should

never be fastened to dry wall or similar material. If this type of

wall is encountered, studs must be located and the bracket

fastened to them. See Figure 4-1.

FIGURE 4-1

002945PC

CONTROL HEAD INSTALLATION
Single Cylinder Installation

For single cylinder system installations the Model MCH3/ECH3/

NMCH3 Control Head can be installed directly onto the cylinder

valve. When the control head is properly aligned in the desired

position, tighten the knurled locking ring to secure the assembly.

See Figure 4-2.

FIGURE 4-2

006214PC / 003647PC

Содержание Kitchen Knight II























































































Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды

Pyro-Chem Kitchen Knight II, Техническое руководство

Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды