Pyro-Chem Kitchen Knight II Скачать руководство пользователя

Страница: 69 / 86

SECTION 4 – SYSTEM INSTALLATION

UL EX3830 ULC EX3830

2014-NOV-10 REV. 06 PagE 4-19

KITCHEN KNIGHT II Restaurant Fire Suppression Manual

SYSTEM CHECkOUT AFTER INSTALLATION (Continued)

Completing System Checkout

1. Make certain the aUTOPULSE control panel is reset and

the control head is re-cocked and set. If the Model SM-120

Solenoid Monitor is used instead of an aUTOPULSE control

panel, energize the actuation/detection circuit by depress-

ing the push button on the solenoid monitor.

2. Using a felt-tipped marker, write the date of installation on

the CO2 pilot cartridge. Ensure that the actuator has an

o-ring installed, and screw the cartridge into the control

head actuator until hand tight. Continue installation of

cartridge by turning an additional 1/4 turn using a wrench or

pliers.

Use caution not to damage cartridge.

Note 1:

Four to five threads should be showing when the

cartridge in engaged properly. It is important that no more

than five threads be showing.

Note 2:

The cartridge and o-ring shall be replaced annually.

CAUTION

Do not over-tighten cartridge. Over-tightening can result in

premature puncturing of the cartridge seal.

3. Remove the pull pin from the hole in the slide plate and

install the control head cover. Insert the pull pin through the

local manual control handle and into the bushing. Secure

the pull pin with the tie provided.

NOTICE

Refer to NFPa-17a for additional inspec-

tion requirements.

ENCLOSURE INSTALLATION INSTRUCTIONS –

MODEL EN-MCU3 AND MODEL EN-S
Enclosure Mounting

The Model EN-MCU3 and/or EN-S Enclosure must be securely

anchored to the wall using bolts or lag screws. The wall to which

the enclosure is attached must be sufficiently strong. The enclo-

sure should never be fastened to drywall or similar material. If

this type of wall is encountered, studs must be located and the

enclosure fastened to them.
Three center mounting holes allow either enclosure to be

mounted on a single stud. Four corner mounting holes are also

available. See Figure 4-32.

FIGURE 4-32

002946PC

Содержание Kitchen Knight II























































































Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды

Pyro-Chem Kitchen Knight II, Техническое руководство

Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды