Pyro-Chem Kitchen Knight II Скачать руководство пользователя

Страница: 52 / 86

SECTION 4 – SYSTEM INSTALLATION

UL EX3830 ULC EX3830

PagE 4-2 REV. 06 2014-NOV-10

KITCHEN KNIGHT II Restaurant Fire Suppression Manual

CONTROL HEAD INSTALLATION (Continued)

Multiple Cylinder Installation

Multiple Cylinder actuation Using MCH3/ECH3/NMCH3

Control Head

The Model MCH3/ECH3/NMCH3 Control Head can be used to

pneumatically actuate a maximum of five agent cylinders with a

16 gram CO2 cartridge. When a control head is used for multiple

cylinder actuation, it cannot be mounted directly onto a cylinder

valve. The control head must be installed remotely using a

Model MB-P2 Control Head Mounting Bracket. The bracket must

be anchored to the wall using bolts or lag screws.

CAUTION

Do not screw the control head directly to a wall as this will warp

the control head, not allowing the mechanism to actuate.

In order to actuate the agent cylinder(s) from a control head, a

1/4 in. NPT x 45° 1/4 in. flare type fitting (conforming to SaE

J513c) or Male Straight Connector (Part No. 32338) must be

screwed into the base of the control head actuator. Pneumatic

tubing or stainless steel actuation hose is then used to connect

the control head to the valve cap assembly of each agent cylin-

der valve. See Figure 4-3.

NOTICE

Pneumatic tubing (copper) used for remote

cylinder actuation shall have an outside diam-

eter of 1/4 in. with a minimum wall thickness

of 1/32 in. (0.8 mm). This is commonly known

as refrigeration-type copper tubing. all tubing

fittings shall be of the 1/4 in., 45° flare type

conforming to SaE J513c.

Compression type fittings are not accept-

able.

a single Model MCH3/ECH3/NMCH3 Control Head can actuate:
1. Up to four cylinders with a maximum of 25 ft (7.6 m) of

copper or stainless steel pneumatic tubing or stainless

steel actuation hose when using an o-ring (Part No. 55531)

installed in place of the Teflon washer and the 16 gram CO2

cartridge.

2. Up to five cylinders with a maximum of 18 ft (5.4 m) of

copper or stainless steel pneumatic tubing or stainless

steel actuation hose when using an o-ring (Part No. 55531)

installed in place of the Teflon washer and the 16 gram CO

cartridge.

CAUTION

Confirm the Teflon washer in the control head actuator assem-

bly has been replaced with the o-ring (Part No. 55531) and the

16 gram CO2 cartridge is installed for four and five cylinder

single control head actuation.

The actuation line must be tested for any leaks by using a hand

held or electric vacuum pump. The pump should be used to draw

a vacuum on the actuation line at the fitting closest to the control

head. a vacuum should be pulled to 20 in. (508 mm) of mercury.

Leaks exceeding 5 in. (127 mm) of mercury within 30 seconds

are not allowed. If the gauge on the vacuum pump indicates a

leak in the line, examine the actuation line for loose fittings or

damage. Correct any leaks and retest.

FIGURE 4-3

004428PC

1/4 IN. OD COPPER TUBINg OR S.S. aCTUaTION HOSE

MaX. 18 FT (5.4 m) FOR FIVE CYLINDER aCTUaTION

MCH3, NMCH3, OR ECH3

CONTROL HEaD

1/4 IN. NPT X 45° 1/4 IN. FLaRE TYPE

FITTINg (SaE J513c) OR MaLE STRaIgHT

CONNECTOR (PaRT NO. 32338)

TO REMaININg

CYLINDERS

45° 1/4 IN. FLaRED

TUBINg NUT WITH

COPPER TUBINg

Содержание Kitchen Knight II























































































Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды

Pyro-Chem Kitchen Knight II, Техническое руководство

Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды