Pyro-Chem Kitchen Knight II страница 59 Скачать руководство пользователя

Страница: 59 / 86

SECTION 4 – SYSTEM INSTALLATION

UL EX3830 ULC EX3830

2014-NOV-10 REV. 06 PagE 4-9

KITCHEN KNIGHT II Restaurant Fire Suppression Manual

REMOTE PULL STATION INSTALLATION (Continued)

The Pull Station can be surface mounted or flush mounted.

For flush mounting a RaCO #232 4 in. (102 mm) deep elec-

trical box or equivalent must be used (dealer supplied). It is

connected to the releasing device using 1/16 in. (1.6 mm)

diameter stainless steel cable. The cable enters the pull station

box through the center hole in the bottom, top, either side,

or the center back hole. The cable enters the control head

through the top-center knockout. The cable must be enclosed in

1/2 in. EMT conduit with a PYRO-CHEM KITCHEN KNIgHT

II corner pulley at each change in conduit direction. Maximum

limitations for the Model RPS-M Remote Mechanical Pull Station

are as follows:

Model RPS-M Cable Run Limitations When Used with

Model ECH3, MCH3, EN-MCU3, and NMCH3 Control Heads

and CBP-1, SBP-1, and WBP-1 Pulley Elbows

Maximum length of cable: 150 ft (45.7 m)

Maximum # of pulleys:

after mounting the pull station box and conduit, feed the stain-

less steel cable from the releasing device, through the conduit,

and into the pull station box. Feed the cable through the bushing

and through the hole provided in the pull handle. Loop the cable

through the pull handle and secure it with the crimp provided

(see Figure 4-17).

FIGURE 4-17

002884PC

Cut and thread the cable through the hole in the latching arm

of the control head and pull the cable tight. Crimp the cable

approximately 6 in. to 8 in. (152 mm to 203 mm) below the

latching arm.

Note:

NFPa-17a requires the pull length to be no

more than 14 in. (355 mm).

NOTICE

Crimps must always be used in conjunc-

tion with two cable lengths. Loops are the

accepted method of connecting the cable

to mechanical components. The crimp must

never be used on a single cable. Exception:

Single cable crimp allowed in detection and

gas valve ratchet wheel using Stop Sleeve

(Part No. 26317) (Packages of 10: Part No.

24919).

Pull the pull handle until the crimp touches the latching arm. See

Figure 4-18. Coil the excess cable in the pull box and attach the

cover plate with the four screws provided. Insert the pull handle

into the cover plate and insert the plastic break rod.

Note:

Excess wire rope must be coiled in the pull station box,

not in the control head.

FIGURE 4-18

006216PC/003647PC

Содержание Kitchen Knight II























































































Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды

Pyro-Chem Kitchen Knight II, Техническое руководство

Результаты поиска

Содержание Kitchen Knight II

Отзывы:

Похожие инструкции для Kitchen Knight II

Бренды по названию

Популярные бренды