PULSION PC8500 Скачать руководство пользователя

Страница: 71 / 105

Installation and setup

Operator´s Manual PiCCO

Page

Version 3.1

C-45

Injection Error - Inject faster than
10 s

Time of injection longer than
10 seconds

Repeat injection rapidly
and smoothly

TD Curve Error - Stabilize patient
temperature and repeat injection

Calculation error of MTt / DSt
caused by temperature
interferences

Eliminate interference and
repeat injection

Baseline Error - Stabilize patient
temperature and repeat injection

Large temperature variations
detected

Eliminate temperature
variations and repeat
injection

Time Out - Repeat fast injection
with cold injectate

Thermodilution curve not
finished within 90 seconds,
possibly very high EVLW with
low CO

Repeat injection with cold
and/or more injectate, if
necessary stabilize
patient

Error: Injectate too warm

Injectate temperature above
blood temperature

Use colder injectate
(< 24°C)

Warning: Injectate too warm

Tinj > 26 °C

Use colder injectate
(< 24°C)

ΔT small

- Use more and/or

colder injectate

∆T <

0.1 °C

Use more and/or colder
injectate

Invalid PCCO Calibration - Check
AP signal and repeat injection

Implausible arterial pressure
signal, signal interferences

Eliminate possible
interferences and repeat
injection

ScvO

Measurement and Calibration

Error Message

Cause

Remedy

ScvO

Calibration Error - Check

optical module and probe

Defective module, probe or
connections

Check module and probe,
if necessary replace and
repeat calibration

Signal too high -
Check probe and position

Artifact due to vessel wall
contact of probe

Check probe, if necessary
relocate and repeat
calibration

Signal too low -
Check probe and position

Probe or module damaged,
defective connector

Check probe, if necessary
replace it and repeat
calibration

Too much ambient light - Check
optical module

Optical module damaged,
defective connector

Check module, if
necessary replace it and
repeat calibration. Avoid
too much ambient light.

Optical module disconnected -
Check optical module and probe
connections

Optical module not
connected

Connect optical module

Содержание PC8500










































































































Результаты поиска

Содержание PC8500

Отзывы:

Похожие инструкции для PC8500

Бренды по названию

Популярные бренды

PULSION PC8500, Руководство оператора и информация о продукте

Результаты поиска

Содержание PC8500

Отзывы:

Похожие инструкции для PC8500

Бренды по названию

Популярные бренды