Produal Proxima WBU Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 63

Produal Proxima WBU Скачать руководство пользователя страница 4

Published: 18.07.2019

4 (63)

1 Network properties

Produal Proxima

®

wireless network is based on Lumenradio MIRA platform that provides a wireless

mesh network with unprecedented scalability and reliability. The Mira network is a self-healing multi-

hop network system that operate on the worldwide license-free 2,4 GHz ISM band. With patented

Future-Proof Coexistence Connectivity (FPCC) technologies we enable connectivity that can safely co-

exist along other wireless technologies, not being interfered or causing interference.

Important:

The network uses 2,4 GHz frequency for communication. The frequency is an

ISM frequency band that can be used worldwide without any licence fees. If you are not sure

about the permissions to use this frequency in your country, contact your local authority for

more information.

Produal Proxima

®

WBU base unit supports up to 100 transmitters and separate repeaters are not

needed. The transmitters work as repeaters without any special configuration.

Only Wireless Produal Proxima

®

MESH 2,4 GHz products are compatible with the network.

MIRA is used for wireless communication between transmitters and base unit. Produal MyTool

®

can’t

communicate with wireless devices using MIRA. Bluetooth is used for communication between Produal

MyTool

®

and wireless devices. The Bluetooth communication can be active with only one device at a

time.

Note:

The wireless devices can use only one communication protocol at a time. The device

is disconnected from the MIRA network when the Bluetooth is activated.

The wireless devices also support Bluetooth beacon messages. Beacon messages are one-way

messages from transmitters and base unit to Produal MyTool

®

application. These messages are used

to send information to application when monitoring or debugging the network.

Signal scanner

also

uses these beacon messages to calculate signal strength between device and application. The beacon

messages can be used also when the device is connected to a MIRA network.
Base unit sends the beacon messages continuously. The transmitter beacon messages can be activated

manually and the messages are active for one hour in following situations.
• During the transmitter installation to network, after the MIRA communication is activated.

Produal Oy | Keltakalliontie 18, FI 48770 Kotka, Finland | tel. +358 10 219 9100 | fax. +358 5 230 9210 | [email protected]

Information is subject to change without prior notice.

EN - 5401comm

«
...
2
3
4
5
6
...
»

Содержание Proxima WBU
































































Отзывы:

Нет отзывов