Polaris 2009 Outlaw 450 MXR Скачать руководство пользователя

Страница: 49 / 205

Features and Controls

Foot Brake

The foot brake operates the rear brakes. The

brake pedal is located in front of the right-hand

footpeg. If the rear wheels slide while using

the foot brake, reduce brake pedal pressure to

brake the wheels without skidding.
Check the brake fluid level frequently for the

foot brake system. The reservoir is located

under the seat. Maintain the fluid level

between the minimum and maximum marks.

WARNING!

Aggressively applying the foot brake when backing down a hill may cause rear tipover,

which could result in serious injury or death. Never back down a hill. Use caution when applying the

foot brake. Do not aggressively apply the foot brake when going forward. The rear wheels may skid

and slide sideways, causing loss of control.

Footpeg

Foot Brake

(Rear Brake)

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды