Polaris 2009 Outlaw 450 MXR Скачать руководство пользователя страница 125

Страница: 125 / 205

122

Maintenance

Spark Plugs

Refer to the specifications section beginning on page 168 for recommended spark plug type

and gap.

NOTICE:

Using non-recommended spark plugs can result in serious engine damage. Always use

Polaris-recommended spark plugs.

Spark plug condition is indicative of engine operation. The spark

plug firing end condition should be read after the engine has been

warmed up and the vehicle has been driven at higher speeds.

Immediately check the spark plug for correct color.
1. Access the spark plug at the right side of the engine.
2. Using the spark plug socket and a wrench, rotate counter-

clockwise to remove the spark plug.

CAUTION!

A hot exhaust system and engine can cause burns. Wear

protective gloves when removing a spark plug for inspection.

3. After reinstalling the spark plug, torque to 14 ft. lbs. (19 Nm).

Spark

Plug

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Бренды по названию

Популярные бренды