Polaris 2009 Outlaw 450 MXR страница 123 Скачать руководство пользователя

Страница: 123 / 205

120

Maintenance

Front Cab/Side Panel Removal

The front cab and side panel assembly is removed in one

piece.
1. Remove the seat.
2. Remove the two front cover screws and remove the front

cover.

3. Remove the eight side panel screws (four on each side).
4. Remove the fuel cap.
5. Gently pull the side panel/cab assembly upward and

rearward.

6. Unplug the key switch and the indicator panel before

removing the cab.

7. To remove a side panel from the cab, remove the corre-

sponding push pin and slide the panel forward to disen-

gage the locking tabs.

Side Panel

Screws

Front Cover

Screws

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды