Polaris 2009 Outlaw 450 MXR Скачать руководство пользователя страница 153

Страница: 153 / 205

150

Maintenance

Handlebar Adjustment

Improper adjustment of the handlebars or incorrect torquing of the adjuster block tightening bolts can

cause limited steering or loosening of the handlebars, resulting in loss of control. Follow the adjustment

procedures exactly, or see your Polaris dealer for service.

The handlebars can be adjusted for rider preference.
1. Loosen the four handlebar bolts.
2. Adjust the handlebar to the desired height. Be

sure the handlebars do not contact the gas tank or

any other part of the machine when turned fully

to the left or right.

3. Torque the two front bolts to 10-12 ft. lbs. (14-16

Nm), then torque the two rear bolts. A gap of up

to 1/8" (3 mm) will remain at the rear bolts.

WARNING

Loosen

bolts

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Бренды по названию

Популярные бренды