Polaris 2009 Outlaw 450 MXR Скачать руководство пользователя

Страница: 157 / 205

154

Maintenance

Front Suspension

Spring Preload

1. Raise and safely support the front of the vehicle off the

ground to allow the suspension to fully extend.

2. Loosen the jam nut and back it away from the adjusting

ring.

3. Turn the adjusting ring to the left (1) to increase preload

for a stiffer ride. Turn the adjusting ring to the right (2) to

decrease preload for a softer ride. See Suspension Set-

tings on page 152.

WARNING!

Uneven adjustment may cause poor handling of the

ATV, which could result in an accident. Always adjust both the left

and right spring preloads equally or have your Polaris dealer

perform the adjustments.

4. Tighten the jam nut firmly against the adjuster ring.

Adjusting

Ring

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды