Polaris 2009 Outlaw 450 MXR Скачать руководство пользователя

Страница: 102 / 205

Maintenance

Engine Oil Level

Check the oil level before each use of the vehi-

cle. If the engine is cold, the oil level should be

visible at the lower edge of the sight glass. If the

engine is warm, the oil level should be visible

between the 1/2 and 3/4 levels in the sight glass.
1. Position the vehicle on a level surface.
2. View the oil level through the sight glass on

the right side of the vehicle.

3. Remove the fill plug and add the recom-

mended oil as needed.

4. Reinstall the fill plug.

Sight Glass

Fill Plug

Warm Level

Cold Level

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды