Polaris 2009 Outlaw 450 MXR страница 144 Скачать руководство пользователя

Страница: 144 / 205

141

Maintenance

Throttle Cable Freeplay Adjustment

Improper adjustment of throttle cable freeplay can result in loss of control, which could result in serious

injury or death. Polaris recommends that this procedure be performed by a Polaris dealer to ensure

that it's done correctly. Mechanically knowledgeable persons who perform this procedure must follow

the adjustment procedures exactly.

1. Locate the throttle cable at the handlebar.
2. Slide the boots off the inline cable adjuster

sleeve and loosen the locking nut.

3. Turn the adjuster until 1/16" to 1/8" (1.5-3 mm)

freeplay is achieved at the thumb lever. While

adjusting freeplay, be sure to flip the throttle

lever back and forth.

4. Tighten the locknut and slide the boots over the cable adjuster until they touch at the

midpoint of the adjuster.

WARNING

Boot

Sleeve

Locking Nut

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды