Polaris 2009 Outlaw 450 MXR страница 88 Скачать руководство пользователя

Страница: 88 / 205

Emission Control Systems

Noise Emission Control System

Do not modify the engine, intake or exhaust components, as doing so may affect compliance

with U.S.A. EPA noise control requirements (40 CFR 205) and local noise level require-

ments.

Operation on Public Lands in the U.S.A.

Your Polaris vehicle has a spark arrestor that was tested and qualified to be in accordance

with the USDA Forest Service Standard 5100-1C. Federal law requires that this spark arres-

tor be installed and functional when the vehicle is operated on public lands.
Operation of off-road vehicles on public lands in the U.S.A. is regulated by 43 CFR

8343.1(c). Violations are subject to monetary penalties. Federal regulations can be viewed

online at www.gpoaccess.gov/ecfr/.

Crankcase Emission Control System

This engine is equipped with a closed crankcase system. Blow-by gases are forced back to

the combustion chamber by the intake system. All exhaust gases exit through the exhaust

system.

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды