Polaris 2009 Outlaw 450 MXR Скачать руководство пользователя

Страница: 61 / 205

Operation

Failure to operate the ATV properly can result in a collision, loss of control, accident or overturn, which

may result in serious injury or death. Read and understand all safety warnings outlined in the safety

section of this owner’s manual.

Break-In Period

The break-in period for your new Polaris ATV is the first three hours of operation, or the

time it takes to use 5-6 gallons (20 liters) of fuel. No single action on your part is as impor-

tant as following the procedures for a proper break-in. Careful treatment of a new engine and

transmission will result in more efficient performance and longer life for both.
Do not allow engine speed to exceed 7000 RPM during the break-in period. Follow the

break-in period with an additional 12 hours of cautious operation, with engine speed below

75% of capacity.

NOTICE:

Failure to perform the recommended break-in maintenance can result in serious engine

damage.

WARNING

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды