Polaris 2009 Outlaw 450 MXR страница 147 Скачать руководство пользователя

Страница: 147 / 205

144

Maintenance

Toe Alignment

Use the following procedure to check the toe alignment of the vehicle. The vehicle is

designed for a neutral toe setting.

WARNING!

Severe injury or death can result from improper toe alignment and adjustment. Do not

attempt to adjust tie rod alignment. All tie rod adjustments should be performed by an authorized

Polaris dealer.

1. Position the vehicle on a level surface.
2. Place the handlebars in a straight-ahead position. Use tie straps to secure the handlebars

to the rear grab bar so they can't move.

Содержание 2009 Outlaw 450 MXR














































































































































































































Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды

Polaris 2009 Outlaw 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2009 Outlaw 450 MXR

Отзывы:

Похожие инструкции для 2009 Outlaw 450 MXR

Бренды по названию

Популярные бренды