Planet MAP-3100 Скачать руководство пользователя страница 79

Страница: 79 / 124

PLANET Mesh Network Manager Guide

•

Data type: Integer, even number only, in between 1500 and 2346

•

Default value is 2346

9) DTIM

Interval

•

Data type: Integer, in between 1 and 256

•

Default value is 1

10) Data Rate

•

Select the data rate of the interface from the list

•

Available selection: Auto, 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps

11) TX Antenna

•

The properties of the transmission antenna

•

Available selection: Diversity, Port1, Port2 and Card Default

12) RX Antenna

•

The properties of the reception antenna

•

Available selection: Diversity, Port1, Port2 and Card Default

13) Current Tx Power (dBm)

•

This is a read-only field indicating the current transmission power used by the

mesh interface.

•

The value is in the unit of dBm

14) Tx Power (dBm)

•

The transmission power field, where user can alter the level of power through the

selection available.

•

The default value for this field is Max, which will use the maximum power level of

the wireless interface.

15) Security

•

The security type to be used by the wireless network, wither open, WEP, or AES

16) Encryption Key

•

The encryption key used in corresponding to the security type used.

•

Data type: Octet String

PLANET Mesh Network Manager Guide

Page79 of 124

Содержание MAP-3100





























































































































Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды

Planet MAP-3100, Руководство пользователя программного обеспечения

Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды