Planet MAP-3100 Скачать руководство пользователя страница 117

Страница: 117 / 124

PLANET Mesh Network Manager Guide

•

A checkbox to enable the access control of the SNMP daemon

manangement

Parameters (SNMP Access Table)

1) Device

•

The name of the device allowed for access control

•

Data type: Octet String

2) Subnet

•

The subnet allowed for access control

•

Data type: IP Address

3) Netmask

•

The netmask for the Subnet IP above

•

Data type: IP Address

4) Using

•

Define the type of access control to use through, either Device or Subnet

5) Comment

•

An optional comment regarding the table entry

•

Data type: Display String

6) Active

•

Define the status of the table entry, either active or inactive

5.3.1.32 Management > SNMP Trap

The SNMP Alarm system embedded in the Mesh AP unit can be configured through this page.

The SNMP Trap Table in this page lists the SNMP Trap hosts.

PLANET Mesh Network Manager Guide

Page117 of 124

Содержание MAP-3100





























































































































Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды

Planet MAP-3100, Руководство пользователя программного обеспечения

Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды