Planet MAP-3100 Скачать руководство пользователя страница 7

Страница: 7 / 124

PLANET Mesh Network Manager Guide

System Requirement

The PLANET Mesh Network Manager is written in JAVA, hence it has the feature of cross

platform, capable to run in most of the platform. The following are the recommended system

requirement.

256 MB RAM (recommended minimum)

10 MB hard disk space

Microsoft Windows 2000, XP (recommended)

Besides, in order to enable the NMS to work properly, the following ports must be allowed

through any firewall between the NMS and the agent:

Port 161 (by default) – Use for standard SNMP Get and Set

Port 162 (by default) – Use for listen to SNMP Trap

Port 4608 (by default) – Used by the Discovery Tool

Port 8188 (by default) – Use to listen for the Layer-2 node’s notification

PLANET Mesh Network Manager Guide

Page7 of 124

Содержание MAP-3100





























































































































Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды

Planet MAP-3100, Руководство пользователя программного обеспечения

Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды