Planet MAP-3100 Скачать руководство пользователя страница 107

Страница: 107 / 124

PLANET Mesh Network Manager Guide

•

Define the status of the table entry, either active or inactive

5.3.1.23 Services > Dynamic DNS

The Dynamic DNS feature of the Mesh AP unit provides the ability to assign and tie the

domain name to a dynamic IP Address. Hence, management from the other site of the

network is able to connect to the device without tracing its IP Address. The page is used to

configure the Dynamic DNS settings.

Parameter

1) Enable Dynamic DNS Service

•

A checkbox to enable or disable the feature of A checkbox to enable or

disable the feature of Dynamic DNS

2) DNS

Provider

•

Select the dynamic DNS provider

•

Available options: dyndns, easydns, no-ip, zoneedit, tzo

3) Hostname

•

The hostname associated with the service provider

•

Data type: Display String

4) Username

•

The username for the dynamic DNS service

•

Data type: Display String

5) Password

•

The password for the username above

•

Data type: Display String

PLANET Mesh Network Manager Guide

Page107 of 124

Содержание MAP-3100





























































































































Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды

Planet MAP-3100, Руководство пользователя программного обеспечения

Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды