Planet MAP-3100 Скачать руководство пользователя страница 46

Страница: 46 / 124

PLANET Mesh Network Manager Guide

The Alarm Level area is to enable the user to determine the level of the warning message

popup and the alarm beep sound. User may drag the slider to alter the level. For instance,

drag the slider of the warning message to Minor, the warning message would not popup if the

level of the alarm received is Warning or Informational. The following figures illustrate the

example of Warning Message, which will be displayed at the left bottom corner of the screen

when the trap is received.

4.2.3.25 Add Trap Agent

This feature is a wizard window, intended to assist the user to set one, or more than one node

to be the trap agent of the host system at the NMS, simultaneously.

Hit the

Add Now

button at the trap viewer mode, to invoke the wizard. At the first page of the

wizard, user will be prompt to enter the IP Address of the desired nodes, to be set as alarm

agent. User can enter the IP Address manually, or select from the drop down list provided.

Click

Next

to proceed.

PLANET Mesh Network Manager Guide

Page46 of 124

Содержание MAP-3100





























































































































Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды

Planet MAP-3100, Руководство пользователя программного обеспечения

Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды