Planet MAP-3100 Скачать руководство пользователя страница 93

Страница: 93 / 124

PLANET Mesh Network Manager Guide

5.3.1.15 Services > MAC Access

The Mac Access feature of the Mesh AP provides a filtering method to limit the accessing of

the client. User can set the Mac Access Table to deny or inversely, allow the client that

defined with their Mac Address to attach to the network.

Parameters:

1) Enable

MAC

Access

•

A checkbox to enable or disable the MAC Access feature

2) Filter

Type

•

Define the filter type of the user not listed in the MAC Access Table, either to

allow or deny the client entries to access the network.

Parameters (MAC Access Table)

1) Mac

Address

•

The Mac Address of the client to be filtered.

•

Data type: Mac Address

PLANET Mesh Network Manager Guide

Page93 of 124

Содержание MAP-3100





























































































































Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды

Planet MAP-3100, Руководство пользователя программного обеспечения

Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды