Planet MAP-3100 Скачать руководство пользователя страница 108

Страница: 108 / 124

PLANET Mesh Network Manager Guide

5.3.1.24 Services > Zero Config

Parameters

1) Enable Zero Config Service

•

A checkbox to enable or disable the Zero Config service of the Mesh AP

2) Handle Client Proxy

•

A checkbox to enable or disable the feature to handle client proxy

3) Proxy

Port

•

The port used in proxy login

•

Data type: Integer, default value is 3001

•

Data range: 1000 ~ 65535

4) Handle Static IP Client

•

A checkbox to enable or disable the feature to handle static IP client

5.3.1.25 Services > Auto IP

The Auto IP Service of the system will assign a unique IP Address to the system. Upon the

successful assignment, a Mesh IP Address and VLAN0 IP Address will be provided. As a

result, the DHCPD settings will be altered to match with the VLAN0 IP.

PLANET Mesh Network Manager Guide

Page108 of 124

Содержание MAP-3100





























































































































Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды

Planet MAP-3100, Руководство пользователя программного обеспечения

Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды