Planet MAP-3100 Скачать руководство пользователя страница 105

Страница: 105 / 124

PLANET Mesh Network Manager Guide

•

The login language: English

5.3.1.22 Services > Radius

The RADIUS server is used to authenticate and store the details of the client who log on to it.

It also used as an accounting protocol for carrying accounting information between the

network access server and a shared accounting server.

Parameters

1) Enable RADIUS Client Service

•

A checkbox to enable or disable the RADIUS Client service

2) NAS

•

The NAS Identifier is a string that use to identify the NAS originating the

Access-Request

•

Data type: Display String

3) Called Station ID

•

The called station ID allows the NAS to send in the Access-Request packet

the phone number that the user called

•

Data type: Display String

PLANET Mesh Network Manager Guide

Page105 of 124

Содержание MAP-3100





























































































































Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды

Planet MAP-3100, Руководство пользователя программного обеспечения

Результаты поиска

Содержание MAP-3100

Отзывы:

Похожие инструкции для MAP-3100

Бренды по названию

Популярные бренды