PERCo IC-05 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 34

PERCo IC-05 Скачать руководство пользователя страница 14

IC-05 Card Capture Reader

13

8.3 Cables parameters

The cables used for connection of the card capture reader are given in Table 1.

Table 1. Recommended cable types

№

Connection

Max. length, m

Cable type

Example

1

IC-05

–

power supply

30

Twisted pair cable with

cross section min. 0.75 mm

2

AWG 18; HO3VV-F 2×0.75

bi-coloured

50

Twisted pair cable with

cross section min. 1.5 mm

2

AWG 15;

2×1.5 bi-coloured

2

IC-05

–

ACS-controller

50

24AWG – 18AWG

(0.2 – 0.8 mm

2

)

RAMCRO SA82BI-T, W8ekw

CABS8/EC, 8C.SEC-SC,

3

Reader board –

ACS-controller,

RS-485

50

Twisted pair cable, min.

Cat5

2×2×0.52, F/UTP2-Cat5e

4

Reader board –

ACS-controller,

Wiegand

50

24AWG – 18AWG

(0.2 – 0.8 mm

2

)

RAMCRO SA82BI-T, W8ekw

CABS8/EC, 8C.SEC-SC,

8.4 Installation

Further installation instructions are given with the earlier mentioned recommendations (see

Clause 8.1 taken into account. Types of cables are stated in Table 1.
Recommendations on preparation of mounting holes in the mounting surface are given

with regard to “SORMAT” PFG IR 10 anchor bolts for solid concrete floors.
Follow this sequence during reader installation:

1. Unpack the card capture reader, check the delivery set completeness.
2. Mark and prepare mounting holes for anchor bolt sleeves on the installation surface

according to Figure 5.

Figure 5. Hole pattern for mounting of the housing

«
...
12
13
14
15
16
...
»

Содержание IC-05



































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды