manualshive.com logo in svg

Parker Automation Gemini GT6K, Справочник по командам

Поделиться
Скачать
Parker Automation Gemini GT6K Скачать руководство пользователя страница 151

 

 

Command Descriptions 

149 

Error Status — Bit #14

:   Bit #14 is set if the input state or position relationship specified in the 

GOWHEN

 command is already true when the 

GO

, 

FGADV

, 

FSHFC

, or 

FSHFD

 command is issued.  The 

error status is monitored and reported only if you enable error-checking bit #14 with the 

ERROR

 

command (e.g., 

ERROR.14-1

).  NOTE: When the error occurs, the drive will branch to the error 

program (assigned with the 

ERRORP

 command). To clear this error condition, issue another 

GOWHEN

 

command; or issue a 

!K

 command and check the program logic (use the 

TRACE

 and 

STEP

 features if 

necessary).

 

ER.14

..... Assignment & comparison operator — use in a conditional expression (see 

AS

).

 

TERF

....... Full text description of each status bit.  (see “

Gowhen condition true

” line item)

 

TER

......... Binary report of each status bit (bits 1-32 from left to right).  See bit #14.

 

GOWHEN

 .

 

.

 

.  on a Trigger Input:  Use 

aTRGFNc1

 

If you wish motion to be triggered with a trigger input, use the 

TRGFNc1

 command. The 

TRGFNc1

 

command executes in the same manner as the 

GOWHEN

 command, except that motion is executed 

when the specified trigger input (

c

) is activated. For more information, refer to the 

TRGFN

 command 

description.

 

GOWHEN

 vs. 

WAIT

:  

 

A 

WAIT

 will cause program flow to halt (except for execution of immediate commands) until the 

condition specified is satisfied. Common uses for this function include delaying subsequent I/O 
activation until the master has achieved a required position or an object has been sensed. 

By contrast, a 

GOWHEN

 will suspend the motion profile until the specified condition is met. It does 

not

 

affect program flow. If you wish motion to be triggered with a trigger input, use the 

TRGFNc1

 

command. The 

TRGFNc1

 command executes in the same manner as the 

GOWHEN

 command, except 

that motion is executed when the specified trigger input (

c

) is activated (see 

TRGFN

 command 

description for details). In addition, 

GOWHEN

 expressions are limited to the operands listed above; 

WAIT

 can use additional operands such as 

FS

 (Following status) and 

VMAS

 (velocity of master). 

Factors Affecting 

GOWHEN

 Execution:

 

If a second 

GOWHEN

 command is executed 

before

 a start-motion command (

GO

, 

FGADV

, 

FSHFC

, or 

FSHFD

), then the first 

GOWHEN

 is over-written by the second 

GOWHEN

 command. (

GOWHEN

 commands 

are not nested.) An error is not generated when a 

GOWHEN

 command is over-written by another 

GOWHEN

.

 

While waiting for a 

GOWHEN

 condition to be met 

and

 a start-motion command 

has

 been issued, if a 

second 

GOWHEN

 command is encountered, then the first sequence is disabled and another start-motion 

command is needed to re-arm the second 

GOWHEN

 sequence.

 

A new 

GOWHEN

 command must be issued for each start-motion command (

GO

, 

FGADV

, 

FSHFC

, or 

FSHFD

). That is, once a 

GOWHEN

 condition is met and the motion command is executed, subsequent 

motion commands will not be affected by the same 

GOWHEN

 command.

 

If the 

GOWHEN

 and start-motion commands are issued, the motion profile is delayed until the 

GOWHEN

 

condition is met. If a second start-motion command is encountered, the second start-motion command 
will override the 

GOWHEN

 command and start motion. If this override situation is not desired, it can be 

avoided by using a 

WAIT

 condition between the first start-motion command and the second start-

motion command.

 

It is probable that the 

GOWHEN

 command, the 

GO

 command, and the 

GOWHEN

 condition becoming true 

may be separated in time, and by other commands. Situations may arise, or commands may be given 
which make the 

GOWHEN

 invalid or inappropriate. In these cases, the 

GOWHEN

 condition is cleared, and 

any motion pending the 

GOWHEN

 condition becoming true is canceled. These situations include 

execution of the 

JOG

, 

JOY

, 

HOM

, 

PRUN

, and 

DRIVEØ

 commands, as well motion being stopped due to 

hard or soft limits, a drive fault, an immediate stop (

!S

), or an immediate kill (

!K

 or 

^K

). 

www.comoso.com

Содержание Gemini GT6K











































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды