manualshive.com logo in svg

Panduit Smartzone PViQ Connectivity System, Руководство пользователя

Поделиться
Скачать
Panduit Smartzone PViQ Connectivity System Скачать руководство пользователя страница 29

 

PVIQ™ CONNECTIVITY SYSTEM USER MANUAL V 1.0 

  

 

28 

 

Appendix G: Interacting with the PViQ™ Connectivity System Interface Units), by the 
Command Line Interface (refer to Appendix C: PViQ™ Connectivity CLI Commands) or 
by the SmartZone Asset and Connectivity Software Modules (refer to the SmartZone 
Software User Manual). Maintenance Mode is implicitly entered through the Web UI 
during firmware update. 

Location Mode 

Location Mode is used to provide visual and audio identification cues to locate specific 
PViQ™ Connectivity Panel. 

Identifying Location Mode 

In Location Mode, the System Status Indicator LED (SYS), will light solid green. The 
MAC, Mode, and TRC Indicator LEDs are off. The following figure shows the PM in 
Location Mode. 

 

Figure 25: PM in Location Mode 

 

In addition, all port LEDs will light solid green, and an audible beep will continue to 
sound. 

 

Figure 26: Panel in Location Mode 

 

To silence the audible beep, press the LEFT Function Key once. The port LEDs will 
remain lit until the panel is taken out of Location Mode. 

Entering Location Mode 

The PViQ Connectivity Patch Panels can only be put into Location Mode using the CLI 
set mode command, as shown below: 

Содержание Smartzone PViQ Connectivity System




















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды