Panasonic S-100PU2E5A Скачать руководство пользователя страница 97

Страница: 97 / 252

1-91

These precautions must be observed without fail.

WARNING

● Before proceeding with the installation work, please read carefully through the installation instructions which are provided with the

indoor unit and also through the installation instructions which you are now reading. In particular, be absolutely sure to read through

the “Safety Precautions” prior to installation. Also ensure that the user keeps these installation instructions in a safe place for future

reference.

■ They describe the instructions using categories which are classified by the extent of the injuries and/or damage caused by incorrect

or improper acts.

■ The actions which must or must not be taken are described using the following pictographs.

■ Panasonic disclaims all liability for any accidents or damages occurring as a result of installing the kit using any procedures

which are not described in the installation instructions or which do not use the specified parts.Any malfunctioning or trouble

caused by the manner in which the kit was installed will not be covered by the terms and conditions of the product warranty.
■ Usage precautions

• Install this air-flow blocking kit before proceeding to install the indoor unit.

• Bear in mind when using the air-flow blocking kit that, depending on the air blocking pattern, it will not be possible to use the

“nanoe” function.

• If use of any separately sold parts is being considered, consult the catalogs, equipment design documents, etc. since some

restrictions apply to how the separately sold parts can be used in combination.

• Keep these installation instructions in a safe place together with the operating instructions of the indoor unit.

■

The installation work should be entrusted to the dealer or the store where the

kit was purchased or to a specialized contractor, and the kit must be installed

correctly using only the specified parts without fail.

(Failure to follow these instructions may cause the unit to fall down and/or water to leak.)

■

The kit must be installed correctly in a location which is strong enough to bear

the weight of all the parts.

(Failure to follow this instruction may result in injuries caused by the unit falling down.)

■ The parts specified by Panasonic must be used as the accessory parts.

(Failure to use the specified parts may cause the unit to fall down and/or water to leak.)

■ The kit must not be installed in a location where flammable gases may leak

in the area around it.

(Failure to follow this instruction may cause ignition if gas should leak and accumulate in the area around

the unit.)

These precautions describe instructions which must be followed in order to avoid personal injuries and/or property damage.

This indicates an action which must not

be taken (that is, an action which is prohibited).

This indicates an action which must be taken

(that is, an action which is mandatory).

CAUTION

Safety Precautions

Selecting the DC fan motor taps

It is necessary to set the fan speed in accordance with the intended application and the optional parts to be

used if any such part is used. (Table 1

)

If this speed is not changed, a reduction in the air flow may result, causing the air outlet temperature to drop

and condensation to form during cooling.

There are two ways to set the fan speed: either (1) change the positions of the DIP switches on the indoor unit

control PCB or (2) set the speed using the wired remote controller. Select one of these ways.

* Priority is given to setting the fan speed by changing the positions of the DIP switches.

TP6

TP3

TP1

2 3

TP6

TP3

TP1

2 3

Intended application /

name of optional parts

Setting

(1)

Item code

5D/5d

setting data

0001

0000

Standard (factory setting)

High-ceiling setting 1

(with standard, ECONAVI panel)

Air-flow blocking kit

(when a duct is connected.)

Intended application /

name of optional parts

Setting

Item code

5D/5d

setting data

(3)

(6)

0003

0006

Air-flow blocking kit(for 3-way air flow)

High-ceiling setting 2

(with standard, ECONAVI panel)

Air-flow blocking kit

(for 2-way air flow)

<Procedure> Be absolutely sure to turn off the

power (earth-leakage circuit breaker).

<1> On Table 1

, check out the “Setting No.” that

corresponds to the intended application and

the optional parts to be used.

<2> Open the cover of the electrical parts box, and

check the indoor unit control PCB. (Fig.

)

<3> Select the Setting No. which was checked out

on Table 1

, and change the positions of the

DIP switches on the indoor unit control PCB.

(1) When setting the fan speed by changing

the positions of the DIP switches on the

indoor unit control PCB

(2) When setting the fan speed using a wired remote controller

(optional parts: CZ-RTC5A)

“OFF” position

1 2 3

TP6

TP3

TP1

2 3

DIP switch

Setting

No.

“OFF” position

“ON” position

DIP switch

“OFF” position

“ON” position

TP6

TP3

TP1

2 3

DIP switch

“ON” position

TP6

TP3

TP1

(3)

(6)

(1)

In the example

shown in the figure

above:
DIP switch 1 is OFF.

DIP switch 2 is ON.

DIP switch 3 is OFF.

On Table 1

, check out the “Item code 5D setting data” that corresponds to the intended

application and the optional parts to be used.

(3) When setting the fan speed using a wired remote controller

(optional parts: CZ-RTC4)

On Table 1

, check out the “Item code 5d setting data” that corresponds to the intended

application and the optional parts to be used.

<1> Hold down the + + buttons together for at least 4 seconds.

The maintenance function screen is displayed.

<2> Use the / buttons to select the display and the / buttons to

select the page.

Select “8.Detailed settings” and press the button.

The [Detailed settings screen] appears.

Using the / buttons, select the unit No.

<3> Using the / buttons, select the item code.

Using the / buttons, change the item code to “5D.”

<4> Using the / buttons, select the setting data.

Using the buttons, change the setting data to the value checked out

on Table 1

, and press the button.

<5> After selecting the unit No. using the / buttons, press the button.

The [Detailed settings completion screen] appears.

Select “Yes” , and press the

<1> Hold down the + + buttons together for at least 4 seconds.

<2> Each time the button is pressed, the numbers of the indoor units under group

control are displayed in sequence.

The fan motor of only the indoor unit that has been selected will run.

<3> Specify item code “5d” using the temperature setting / buttons.

<4> Change the setting data using the hour buttons. The setting data details

are as given on Table 1

<5> Press the button. (OK if the display changes from flashing to lighted.)

<6> Press the button. The normal stop status is established.

Go to step <2> to change the selected indoor unit.

<7> Press the button. The normal stop status is established.

(1)

0001

Ｄ

Unit No.

Setting data

Item code

<Procedure> Ensure that the units have stopped operating before changing the fan speed.

<Procedure> Ensure that the unit has stopped operating before changing the fan speed.

Applicable indoor units:4-Way Cassette

INSTALLATION INSTRUCTIONS

Air-flow blocking kit

Model No.CZ-CFU3

85464369937001

Printed in JAPAN

PA0816-10816

CV6233336299

WARNING

CAUTION

NOTES

DC fan motor tap setting table

Table 1

Indoor unit control PCB

Fig.

This symbol refers to a hazard or

unsafe practice which can result in

severe personal injury or death.

This symbol refers to a hazard or

unsafe practice which can result in

personal injury or product or property

damage.

SM830252-01_欧州_Single_8・10HP_TD_SM.indb 91

16/10/14 13:58:06

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание S-100PU2E5A




























































































































































































































































Результаты поиска

Содержание S-100PU2E5A

Отзывы:

Похожие инструкции для S-100PU2E5A

Бренды по названию

Популярные бренды

Panasonic S-100PU2E5A, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-100PU2E5A

Отзывы:

Похожие инструкции для S-100PU2E5A

Бренды по названию

Популярные бренды