Panasonic PT-FW430EA Скачать руководство пользователя

Страница: 72 / 89

Replacement

- ENGLISH

Maintenance

Lamp unit

The lamp unit is a consumable component. You can check the total usage time using STATUS in the

PROJECTOR SETUP menu on page 56.

It is recommended to ask an authorized engineer to replace the lamp unit. Contact your dealer.

Consult your dealer to purchase a replacement lamp unit (ET-LAF100A, dealt as a service component).

CAUTION:

■ Do not replace the lamp unit when it is hot. (Wait at least one hour after use.)

The inside of the cover can become very hot, take care to avoid burn injuries.

Notes on the replacement of the lamp unit

The luminous source of the lamp is made of glass and may burst if

you hit it against a hard surface or drop it.

Please handle with care.

A Phillips screwdriver is required for replacement of the lamp unit.

When replacing the lamp unit, be sure to hold it by the handle.

Hold the lamp unit horizontally while replacing it to prevent fragments

of glass from scattering, in case the lamp breaks. When the projector

is mounted on a ceiling, do not work directly under the projector or put

your face close to the projector. Pull the old lamp unit out horizontally.

The lamp contains mercury. Consult your local municipality or your

dealer about correct disposal of used lamp units.

Attention

Do not use other than designated lamp units.

The part numbers of accessories and separately sold components are subject to change without notice.

When to replace the lamp unit

The lamp unit is a consumable component. Brightness decreases according to duration of usage, so periodical

replacement of the lamp unit is necessary. 6000 hours of use is a rough guideline for replacement. However,

a lamp unit may not light before 6000 hours of use, depending on individual lamp, usage, and environmental

conditions. It is recommended to prepare spare units in advance. The risk of the lamp bursting increases after

6000 hours of use. To prevent this, the projector will automatically turn the lamp off approximately ten minutes

after it is turned on in such cases. It is recommended that you replace the lamp unit before this occurs.

On screen

LAMP indicator

LAMP

Over 5800 hours

The message is displayed for 30 seconds. If you

press any button within the 30 seconds, the message

disappears.

Lights in red (even in

stand-by mode).

Over 6000 hours

After ten minutes, the projector shuts off the power

automatically.

Note

6000 hours of use is a rough guideline, but this is not a guarantee.

REPLACE LAMP

Содержание PT-FW430EA


























































































Результаты поиска

Содержание PT-FW430EA

Отзывы:

Похожие инструкции для PT-FW430EA

Бренды по названию

Популярные бренды

Panasonic PT-FW430EA, Руководство по эксплуатации

Результаты поиска

Содержание PT-FW430EA

Отзывы:

Похожие инструкции для PT-FW430EA

Бренды по названию

Популярные бренды