Panasonic PT-FW430EA Скачать руководство пользователя страница 71

Страница: 71 / 89

Replacement

ENGLISH -

Maintenance

Drying the air filter unit

Leave the filters to dry in a well-

•

ventilated location that is not exposed

to excessive dust.

Install the air filter unit to the projector.

4 )

The air filter unit has no distinction between top

and bottom.

Perform step

in the reverse order.

Attach the air filter cover to the

5 )

projector and secure the filter cover

screw using a Phillips screwdriver.

Perform step

in the reverse order.

Attention

After cleaning the air filter unit, make sure that it is

sufficiently dry before reinstalling it to the projector.

Installing the air filter unit while it is wet will result in

electric shock or malfunction.

Note

Be sure to install the air filter properly. If the projector

is operated without the air filter installed, the projector

will shut off after ten minutes to prevent damage from

incoming dirt and dust. (In such cases, the remaining

time before shutdown is displayed in one-minute

increments.)

Replace the air filter with a replacement filter unit (ET-

EMF100) when cleaning fails to remove dirt or dust, or

when the air filter unit breaks.

Air filter replacement is recommended after cleaning the

unit two times.

The dust-proof properties may reduce after each

cleaning.

Replacing the unit

Air filter unit

Replace the air filter when cleaning fails to remove dirt or dust.

Replace it with the separately sold ET-EMF100 replacement filter unit. Consult your supplier when you

purchase a replacement filter.

Replacement of the air filter unit

Remove the air filter cover.

1 )

Use a Phillips screwdriver to turn the air filter

cover screw counterclockwise until the screw

turns freely to remove the air filter cover.

Remove the air filter unit.

2 )

Pull the air filter unit out from the projector

holding the tab of the air filter unit.

Attach the separately sold replacement

3 )

filter unit (ET-EMF100) to the projector.

The air filter unit has no distinction between top

and bottom.

Attach the air filter unit by performing step 2) in

reverse order.

Attach the air filter cover to the

4 )

projector and tighten the air filter cover

screw using a Phillips screwdriver.

Attach the air filter cover by performing step 1)

in reverse order.

Attention

Turn off the power before you replace the air filter

unit.

When attaching the air filter unit, make sure that

the projector is stable, and work in an environment

that is safe, even in the event of the air filter unit

dropping.

Do not turn on the projector without an air filter

unit attached. If the projector is used without the

air filter, dirt and dust that enters the projector may

damage it.

Air filter cover screw

Air filter cover

Knobs

Air filter unit

Содержание PT-FW430EA


























































































Результаты поиска

Содержание PT-FW430EA

Отзывы:

Похожие инструкции для PT-FW430EA

Бренды по названию

Популярные бренды

Panasonic PT-FW430EA, Руководство по эксплуатации

Результаты поиска

Содержание PT-FW430EA

Отзывы:

Похожие инструкции для PT-FW430EA

Бренды по названию

Популярные бренды