Panasonic PT-FW430EA Скачать руководство пользователя страница 40

Страница: 40 / 89

PICTURE menu

- ENGLISH

Settings

ADVANCED MENU

Press ▲▼ to select the [ADVANCED

1 )

MENU].
Press the <ENTER> button.

2 )

The [ADVANCED MENU] screen appears.

Press ▲▼ to select settings between

3 )

[CONTRAST R] and [BRIGHTNESS B].

Press ▲▼ or the <ENTER> button.

4 )

Use ▲▼ to adjust the level.

5 )

Adjustments can be made in the range +32

(maximum) to -32 (minimum).

Adjustment

Operation

Result

CONTRAST R

Press ►.

Emphasizes red in

highlight areas

Press ◄.

Deemphasizes red

in highlight areas

CONTRAST G

Press ►.

Emphasizes green

in highlight areas

Press ◄.

Deemphasizes

green in highlight

areas

CONTRAST B

Press ►.

Emphasizes blue in

highlight areas

Press ◄.

Deemphasizes blue

in highlight areas

BRIGHTNESS R

Press ►.

Emphasizes red in

shadow areas

Press ◄.

Deemphasizes red

in shadow areas

BRIGHTNESS G

Press ►.

Emphasizes green

in shadow areas

Press ◄.

Deemphasizes

green in shadow

areas

BRIGHTNESS B

Press ►.

Emphasizes blue in

shadow areas

Press ◄.

Deemphasizes blue

in shadow areas

DAYLIGHT VIEW

This corrects images so that they appear vivid when

projected under bright lighting.

Press ▲▼ to select [DAYLIGHT VIEW].

1 )

Press ◄► or the <ENTER> button.

2 )

The [DAYLIGHT VIEW] individual adjustment

screen will be displayed.

Press ◄► to switch [DAYLIGHT VIEW].

3 )

The setting will change as follows each time

you press the button.

AUTO

OFF

AUTO

Automatically adjustment to suit ambient

brightness

Enable DAYLIGHT VIEW

OFF

Disable DAYLIGHT VIEW

Note

You can not set [AUTO] if [REAR/DESK] or [REAR

CEILING] is selected for [PROJECTION METHOD] of

[PROJECTOR SETUP].

The [AUTO] mode may not function properly if an object

is placed on the top of the projector.

DIGITAL CINEMA REALITY

You can improve the vertical resolution of 2-2 and 2-3

pulldown video.

This function is available only with the following signal

inputs.

(525i(480i), 625i(576i), 1125(1080)/60i,

1125(1080)/50i)

Press ▲▼ to select [DIGITAL CINEMA

1 )

REALITY].

Press ◄► or the <ENTER> button.

2 )

The [DIGITAL CINEMA REALITY] screen

appears.

Press ◄► to switch [DIGITAL CINEMA

3 )

REALITY] settings.

Each press of the button switches the settings

as shown below.

OFF

Disable DIGITAL CINEMA REALITY

Enable DIGITAL CINEMA REALITY

Содержание PT-FW430EA


























































































Результаты поиска

Содержание PT-FW430EA

Отзывы:

Похожие инструкции для PT-FW430EA

Бренды по названию

Популярные бренды

Panasonic PT-FW430EA, Руководство по эксплуатации

Результаты поиска

Содержание PT-FW430EA

Отзывы:

Похожие инструкции для PT-FW430EA

Бренды по названию

Популярные бренды