Panasonic LightPix AE20 Скачать руководство пользователя страница 73

Страница: 73 / 151

TEACH: OKNG (Teaching for OK and NG products)

In INSPECTION (or RUN)
mode

TEACHING mode (“TEACH” is displayed.)

Upper line- Binary level: 0 – 255

(default: 150)

<3>: Decreases the value
<4>: Increases the value

Lower line-Exposure time: 0.03 to
50.00 ms

(default: 1.93)

<7>: Shortens the exposure time
<8>: Extends the exposure time
If you want to perform a teaching at this
point, press <6> first and then <1>.

SIZE: Resizes the inspection area

If you want to execute a teaching at this
point, press <6> first and then <1> after
resizing.

MOVE: Moves inspection area

<6>: Executes a teaching for the
current product type

Teaching for the current product type is
executed.

STNG: Teaching for OK
products-Normal completion
FAIL: Abnormal termination of
teaching

→

The ALARM signal is output.

<6>: Executes a teaching

Executes a teaching for NG product of
the current product type

DONE: Teaching for NG
product-Normal completion
FAIL: Abnormal teaching

(the ALARM signal is output.)

<5>: Returns to the top.

You can always
switch the product
types by pressing
<2> and <5> buttons
at the same time.

If the ALARM signal is output after teaching is completed, the signal is held ON until teaching is
successfully completed. As long as the unit keeps outputting the ALARM signal, it cannot properly
execute an inspection.

Содержание LightPix AE20
























































































































































Результаты поиска

Содержание LightPix AE20

Отзывы:

Похожие инструкции для LightPix AE20

Бренды по названию

Популярные бренды

Panasonic LightPix AE20, Руководство пользователя

Результаты поиска

Содержание LightPix AE20

Отзывы:

Похожие инструкции для LightPix AE20

Бренды по названию

Популярные бренды