Panasonic LightPix AE20 Скачать руководство пользователя страница 15

Страница: 15 / 151

2.2.2 Texts

Displayed on the LCD Monitor of the Operation Unit

The display area of the operation unit displays measurement data and setting values and operating status of
the LightPixAE20 as a text string.

Displayed
text

Mode

Description

SET

CONFIGURATION mode

Indicates the LightPixAE20 is in CONFIGURATION mode

RUN

RUN (RUN VIEW) mode

Indicates the LightPixAE20 is in RUN mode.

TEACH

TEACHING mode

Indicates the LightPixAE20 is in TEACHING mode.

VIEW

RUN VIEW mode

Indicates the LightPixAE20 is RUNVIEW mode. In this mode,
captured images are displayed on the finder unit.

READY

RUN (RUN VIEW) mode
TEACHING mode

Displayed when parallel output signal “READY” is ON.

LOCK

RUN (VIEW) mode

Means the lock function is activated. In this mode, you cannot
operate the LightPixAE20.

ALARM
(Red)

RUN (VIEW) mode
TEACHING mode
(May be displayed when the
device is in the other
modes.)

Displayed when the parallel output signal “ALARM” is ON.

OUT1-3

RUN (RUN VIEW) mode

Represents output state of parallel output signals OUT1-3. The
signals that are turned on are displayed.

For example,

•

OUT 1 2: OUT1 and OUT2 signals are on.

RUN (RUN VIEW) mode

Indicates the unit for the measured data is millimeter. You can
check it only if you are using the following applications:

•

Color Pattern Matching

•

Edge

•

Peak

•

Measurement

RUN (RUN VIEW) mode

Indicates the unit for the measured data is square millimeter.
You can check it only if you are using the following applications:

•

Color Area

•

Color Judgement

Содержание LightPix AE20
























































































































































Результаты поиска

Содержание LightPix AE20

Отзывы:

Panasonic LightPix AE20, Руководство пользователя, Страница: 15 / 151

Результаты поиска

Содержание LightPix AE20

Отзывы: