Panasonic LightPix AE20 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 151

background image

4.2 Color Area and Color Judgement

4.2.1 Overview of Color Area

The Color Area application is used for measuring the registered color area. It judges whether or not the
measured color area values are within the set area range, and if the color area values are within the range
(OK judgement), the OUT1 signal is turned on, if they are out of the range (NG judgement), the OUT1
signal is turned off. You can register one product type for each color and totally seven colors for seven
product types, but inspection is performed for each product type. If you want to inspect the object in the
color different from the color that is saved as the current product type, change to the desired product type at
the LightPix side first and continue the inspection.

Example:
Registered data

Area range

Product
type No.

Registered
color

Min.

Max.

1 Red

200

300

2 Blue 200

300

Operations of AE20

32

«
...
37
38
39
40
41
...
»

Содержание LightPix AE20
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для LightPix AE20

Бренд: Nautel Страницы: 205

Бренд: S&P Страницы: 4

Бренд: Galaxy Страницы: 12

Бренд: Galaxy Страницы: 11

Бренд: l-com Страницы: 6

Бренд: E+E Elektronik Страницы: 36

Бренд: AeroComm Страницы: 57

LRS Connect TX-7471

Бренд: Long Range Systems Страницы: 53

Multi-Code 1051

Бренд: Linear Страницы: 2

Бренд: SenseAir Страницы: 14

Бренд: Northern Страницы: 4

Бренд: Vaisala Страницы: 16

Бренд: TILLQUIST Страницы: 15

Бренд: GO Systemelektronik Страницы: 55

Бренд: Alinco Страницы: 49

Бренд: ADN pesage Страницы: 39

Бренд: Bosch Страницы: 36

Бренд: Intek Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды