Panasonic LightPix AE20 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 151

background image

5.2.4 Teaching

The LightPixAE20 can execute a teaching using the signals from the external devices based on the currently
captured image, but exposure time and binary level may be changed after teaching execution. Therefore,
execute a teaching only if there is no problem having these values changed.

Timing chart: Teaching for OK product only

1. Make sure the READY signal is ON and inptu the TEACH signal.

2. Input a product type, for which you want to peform a teaching, to the ports of TYPE 1-3 in more

than two milliseconds (T1).

3. After two milliseconds (T2), input the TRIGGER signal.

Input the TRIGGER signal for the following time period.

Used inspection application

Time period of T3

Color Area, Color Judgement, Color
Pattern Matching

750 ms or longer

Edge detection, Peak, Measurement

350 ms or longer

The READY signal is turned off and a teaching is executed. (“ADJ” is displayed on the operation unit.)
After the teaching is completed, the READY signal is turned on. If the unit failed to complete the teaching, the
ALARM signal is turned on.

4. Turn the TEACH signal off and switch to INSPECTION (RUN, RUN VIEW) mode.

When the ALARM signal is turned on at the previous step, it keeps on until the teaching is successfully complete.

If the ALARM signal is output after teaching, adjust exposure time and binary level using the operation

unit or AETOOL. As long as the unit keeps outputting the ALARM signal, it cannot execute an inspection
properly.

104

«
...
109
110
111
112
113
...
»

Содержание LightPix AE20
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для LightPix AE20

Бренд: Camille Bauer Страницы: 19

Бренд: E+E Elektronik Страницы: 2

Бренд: R.V.R. Elettronica Страницы: 12

Бренд: aci Страницы: 8

Бренд: aci Страницы: 4

Бренд: Icom Страницы: 9

Бренд: HBK Страницы: 40

Бренд: HBK Страницы: 104

Бренд: Inovonics Страницы: 2

Бренд: Evikon Страницы: 4

Бренд: Samson Страницы: 24

Бренд: Shure Страницы: 4

Бренд: Clarion Страницы: 23

FMT 380 BT CHARGE

Бренд: Hyundai Страницы: 24

Бренд: Yaesu Страницы: 3

Бренд: TQ-Systems Страницы: 20

Бренд: BriarTek Страницы: 10

Бренд: Delta-Opti Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды