Panasonic LightPix AE20 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 151

Panasonic LightPix AE20 Скачать руководство пользователя страница 9

1.1 Overview

LightPixAE20 (hereinafter called “the LightPixAE20”) is a device that is integrated with CPU, camera, lens
and lighting equipment. With AETOOL software for the LightPixAE20 (free), you can download one of the
inspection applications to the main unit, check scanning conditions or images and document the images
stored in the main unit (or save them as bmp file).

In addition, with the operation unit and finder unit, you can check the current image or modify the scanning
conditions, and with our programmable display GT11, you can change settings or control start of code read.

The operating instructions mainly for the operation unit and finder unit are described in this manual.
Refer to the AETOOL help files (available after installation) for further details of the AETOOL.

About the AETOOL: Page 134

2

«
...
7
8
9
10
11
...
»

Содержание LightPix AE20
























































































































































Отзывы:

Нет отзывов