Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 96

Страница: 96 / 160

Chapter 6. Serial Communications

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

6.3 Checking the DF868 Baud Rate

For successful serial communications, the DF868 and the personal computer must be set up to send/receive data at

the same speed. To check the

baud rate

setting of the DF868, proceed as follows:

Access the

User Program

, by pressing the

[PROG]

key on the keypad. The standard measurement mode screen is

replaced by the following initial programming mode screen:

The available rates are 300, 600, 1200, 2400, 4800, 9600 and 19200 baud. After verifying or changing the baud rate

setting, press the

[EXIT]

key three times to return to standard measurement mode.

Note:

Refer to Chapter 1,

Programming Site Data

, for a detailed description of using the

COMM

submenu.

6.4 Setting Up the Terminal Software

To communicate with personal computers running under either the Windows 3.X or Windows 9X/NT operating

systems, please refer to “Terminal Communications Software” in the brochure

EIA-RS Serial Communications

(916-

054).

Note:

For computers operating under other operating systems, contact the factory for assistance or consult the

operating system manual supplied with the computer.

PROGRAM Start

‰

Press the

[F3]

key to select the

GLOBL

menu.

PROGRAM
previous selection appears

here

CH1

CH2

GLOB

SAVE

PROGRAM Start

‰

Press the

[F4]

key to select the

COMM

submenu.

Global PROGRAM
previous selection appears

here

CLOCK

SYSTM

I/O

COMM

Global COMM PROGRAM

‰

To change the baud rate, press the [



key until the desired baud rate appears

on the option bar, and then press the appropriate

[Fx]

function key.

Global PROGRAM
Comm port

BAUD RATE
current setting appears here

4800

9600

19200

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 96 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: