Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 76

Страница: 76 / 160

Chapter 3. Logging Data

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

3.2.3 START DATE Prompt

11.

Press

[F1]

to accept the displayed

Start Date

or press

[F2]

to enter a different start date. To start logging today,

press

[F3]

• If

TODAY

was selected, proceed to step 12 for a non-circular log or to step 14 for a circular log.

• Otherwise, continue with the next prompt to

Edit

the Start Date.

Enter the desired

Year

and press

[ENT]

. The acceptable range is 0 to 99.

Use the [



, [



and

[F1]-[F4]

keys to select the desired

Month.

Enter the desired

Day

and press

[ENT]

. The acceptable range is 1 to the number of days in the selected

month (28, 29, 30 or 31).

3.2.4 END TIME Prompt

12.

Press

[F1]

to accept the displayed

End Time

or press

[F2]

to enter a different end time. To select a specific time

period for the log to run, press

[F3]

•

was selected, proceed to the

END DATE

prompt.

•

TIMED

was selected, proceed to the

LOG TIME

prompt.

•

EDIT

was selected, complete the steps below.

Note:

The log

END TIME

must exceed the log

START TIME

by at least five minutes. Failure to observe this restriction

will result in an error message.

Press

[F1]

for

or press

[F2]

for

. Then, enter the desired

Hour

and press

[ENT]

. The acceptable range is 1 to 12.

Enter the desired

Minutes

and press

[ENT]

. The acceptable range is 0 to 59.

Enter the desired

Seconds

and press

[ENT]

. The acceptable range is 0 to 59.

3.2.5 END DATE Prompt

13.

Press

[F1]

to accept the displayed

End Date

or press

[F2]

to enter a different end date. To end the log today, press

[F3]

• If

TODAY

was selected, proceed to the

TIME INCREMENT

prompt.

• Otherwise, complete the steps below.

Enter the desired

Year

and press

[ENT]

. The acceptable range is 0 to 99.

Use the [



, [



and

[F1]-[F4]

keys to select the desired

Month

Enter the desired

Day

and press

[ENT]

. The acceptable range is 1 to the number of days in the selected

month (28, 29, 30 or 31). The program proceeds to step 15.

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 76 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: