Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 75

Страница: 75 / 160

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

Chapter 3. Logging Data

3.2 Creating a Standard Log (cont.)

Refer to Chapter 3 of the

Service Manual

for a discussion of the many parameters accessible via the

DIAG

option.

Note:

The units assigned to the parameters in Table 35 on page 66 are those selected in the

User Program

(

SYSTM

submenu)

Use the [



, [



and

[F1]-[F4]

keys to select the second parameter to be logged. See Table 35 on page 66 for a

list of the available options.

Use the [



, [



and

[F1]-[F4]

keys to select the third parameter to be logged. See Table 35 on page 66 for a list

of the available options.

• If you selected a totalized value for display, go to step 8.
• If you did not, go to step 9.

At the

Set LOG Totals to 0?

prompt, press

[F1]

to leave the log totals at their present value or press

[F2]

to reset

the log totals to zero.

Note:

The

Set LOG Totals to 0?

prompt only appears if either

+TOTL

-TOTL

was selected as one of the three

parameters to log. Choosing

YES

at this prompt only resets the log totals to zero and has no effect on the

meter totals.

3.2.1

Log Type

Press

[F1]

to create a non-circular log or press

[F2]

to create a circular log.

A non-circular log automatically stops when the meter runs out of memory or the specified

END TIME

is reached. A

circular log runs continuously until manually stopped, but only the data from the most recent log cycle is saved. At

the start of each cycle, the oldest recorded data is overwritten by the new data from the current cycle.

CAUTION!

If data from one circular log cycle exceeds the meter’s memory capacity, the earliest logged data will

be lost.

3.2.2 STARTTIME Prompt

10.

Press

[F1]

to accept the displayed

Start Time

or press

[F2]

to enter a different start time. To start logging

immediately, press

[F3]

•

was selected, proceed to step 11.

•

NOW

was selected, proceed to step 12 if you selected a non-circular log or to step 14 for a circular log.

•

EDIT

was selected, complete the steps listed below.

Press

[F1]-[F2]

to select

. Then, enter the desired

Hour

(1-12) and press

[ENT]

. (Entry of a start time earlier

than the current time will generate an error message.)

Enter the desired

Minutes

and press

[ENT]

. The acceptable range is 0 to 59.

Enter the desired

Seconds

and press

[ENT]

. The acceptable range is 0 to 59.

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 75 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: