Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 19

Страница: 19 / 160

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

Chapter 1. Programming Site Data

1.6 Entering Channel Data

While following the programming instructions, refer to the menu map in Figure 10 on page 97 or Figure 11 on page 98

After selecting

[F1]=CH1

(or

[F2]=CH2

) at the initial programming screen, the following screen appears:

Based on the selection made above, proceed to the appropriate section of this chapter for instructions.

1.6.1

Activating a Channel

The

ACTIV

submenu activates a channel and selects the desired measurement method.

To enter the

Channel PROGRAM

menu, press

[F1]

[F2] (depending on the desired channel) at the User

PROGRAM

prompt.

Enter the

ACTIV

submenu by pressing

[F1]

at the

Channel PROGRAM

prompt.

Press

[F1]

to deactivate the channel,

[F2]

to activate Channel 1 in

Transit-Time

mode, or

[F3]

to activate

TransFlection

mode.

The Model DF868 flowmeter can take measurements in two ways:
•

The Correlation Transit-Time™ technique uses a pair of transducers (either wetted or clamp-on) with each

transducer alternately sending and receiving coded ultrasonic signals through the fluid. When the fluid is flowing,

signal transit time in the downstream direction is shorter than in the upstream direction; the difference between

these transit times is proportional to the flow velocity. The DF868 measures this very small time difference and,

using various digital signal processing techniques combined with programmed pipe parameters, determines

the flow rate and direction.

•

The TransFlection

technique uses two transducers. One transducer shoots thousands of grouped ultrasonic

pulses in very rapid succession. The pulses bounce off “scatterers” in the liquid (bubbles, solids, or liquid droplets)

and are reflected back to the other transducer. Each received pulse group receives a “snapshot” of the flow. By

comparing all snapshots and averaging out objects that do not appear to move with the flow, the DF868 can

determine flow rate and direction.

Note:

If the DF868 has not been ordered with TransFlection mode, the TRNFL option does not appear.

Proceed directly to the next section to program the

SYSTM

submenu.

Chan 1

PROGR

Start

‰

Press the [



and [



keys and a function key

[F1]-[F4]

to select the desired

submenu. From this screen, press

[EXIT]

to return to the initial

User Program

screen shown on page 1-8.

Channel PROGRAM
status

ACTIV

SYSTM

PIPE

I/O

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 19 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: