Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 95

Страница: 95 / 160

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

Chapter 6. Serial Communications

Chapter 6. Serial Communications

6.1 Introduction

The Model DF868 flowmeter is equipped with a standard RS232 serial interface. By using this interface, any log files

stored in the DF868’s memory may be easily uploaded to a personal computer. In order to accomplish this, the

following steps must be completed:

Note:

See

EIA-RS Serial Communications (916-054)

for a more detailed discussion.

•

Connect the DF868 to the personal computer

•

Check the DF868 baud rate setting

•

Set up the personal computer’s terminal software

•

Transfer the log files to the personal computer.

This section also contains instructions for setting up an RS485 serial interface.

6.2 Wiring the RS232 Interface

The first step is to connect the built-in RS232 port in the DF868 to one of the serial ports (COM1 or COM2) on the

personal computer. Table 39 lists the standard cables available from the factory for this purpose.

Each of the cables listed in Table 39 is available in several standard lengths. However, a user-supplied cable may be

used, if preferred. In either case, wire the DF868 end of the serial cable in accordance with the pin designations listed

in Table 1 in the brochure,

EIA-RS Serial Communications

(916-054)

Note:

For serial communications between a single DF868 and a single personal computer, no connections are

required to pins 4 and 5 of the DF868’s serial connector. However, these pins should be jumpered together to

ensure proper operation.

Table 39: Panametrics Serial Cables

Part Number

PC Connector

DF868 Connector

704-659

DB25 Male

Flying Leads (5)

704-660

DB9 Male

Flying Leads (5)

704-661

DB25 Female

Flying Leads (5)

704-662

DB9 Female

Flying Leads (5)

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 95 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: