Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 89

Страница: 89 / 160

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

Chapter 4. Printing Data

4.4.1 Numeric Format

After the numeric format (and starting page and number of pages, if applicable) is chosen, the Model DF868 returns

to the standard data display screen and begins printing the log file. The printout continues until the entire log has

been printed or until a

STOP

command is issued (see the instructions for the

STOP

submenu on page 83). A portion of

a typical printout is shown in Figure 5.

Figure 5: A Typical Numeric Printout

4.4.2 Graphical Format

After the graphical format (and starting page and number of pages, if applicable) is chosen, the following additional

prompts must be answered:

Enter the desired maximum value for the Y (vertical) axis and press

[ENT]

Note:

Enter a

Y AXIS MAX

value that is larger than the largest logged measurement value.

At the

Y Range

prompt, press

[F1]

to show only the positive Y axis or press

[F2]

to display both the positive and

negative y axis.

The Model DF868 returns to the standard data display screen and begins printing the log file. The printout continues

until the entire log has been printed or until a

STOP

command is issued (see the instructions for the

STOP

submenu

on page 83). A portion of a typical printout is shown in Figure 6.

Figure 6: A Typical Graphical Log Printout

4.5 Print Site File

Use the

PROG

submenu to print the data in a site file that was set up and saved as described in Chapter 1,

Programming Site Data

. To print a site file, refer to Figure 16 on page 103

and complete the following steps:

IMPORTANT:

Make sure that a printer has been properly set up before proceeding with this section.

To access the

Print Menu

, press the

[PRNT]

key.

LOG TITLE:
START:
END:
INTERVAL:

HH:MM:SS
11:50:45
11:50:55
11:51:05
11:51:15

11:51:25
11:51:35
11:51:45
11:51:55
11:52:05
11:52:15
    .
    .
    .

ACF/HR
686.85

684.00

678.12

680.58

670.70

675.99

669.79

675.59

662.28

666.71

ID#1 VOLUM

232.57

236.34

234.46

ACF

230.45

228.58

226.71

224.84

222.70

220.83

218.92

ID#2 +TOTL

9 SEP 97 11:54:45
10 seconds

1039.082

1038.860

1039.255

FT/S

1039.511

1039.105

1039.137

1039.470

1039.509

1039.003

1039.147

ID#1 SNDSP

9 SEP 97 11:50:43

LOG1

09-09-97

09-09-97
09-09-97
.

09-09-97
09-09-97
09-09-97

09-09-97
09-09-97
09-09-97
09-09-97

MM:DD:YY

TIME

DATE

.
.

0.0

1.0

0.0

1.0

LOG MESSAGE

LOG NAME

X-AXIS 50 seconds PER-DIV

Y-AXIS MAX 500 ACF/M

START TIME

03:27:01 PM

20 OCT 97

END TIME

03:28:46 PM

20 OCT 97

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 89 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: