Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 100

Страница: 100 / 160

Chapter 6. Serial Communications

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

6.5.3.1

Reconfiguring a Serial Interface Converter (cont.)

Reassemble the serial interface converter and secure it to the mounting bracket with the two mounting screws.

Reinstall the mounting bracket into the electronics enclosure and secure it with the standoff and the grounding

screw.

6.5.3.2

Wiring the System

After the serial interface converters have been configured for multi-point operation, the system can be wired.

Using

twisted-wire pairs

, connect the XMT+ terminals of all the flowmeters together and connect the XMT–

terminals of all the flowmeters together.

IMPORTANT:

Make sure that the flowmeter with the non-modified converter is wired as the last unit in the chain.

Using a

twisted-wire pair

, connect the XMT+ terminal of the barrier strip to the T+/R+ terminal of the PC’s RS485

adapter and connect the XMT– terminal of the barrier strip to the T-/R- terminal of the PC’s RS485 adapter (see

the documentation provided with the RS485 adapter for details).

Note:

The XMT+ terminal on the barrier strip is the screw opposite the red wire connection and the XMT– terminal

on the barrier strip is the screw opposite the green wire connection.

Reinstall the clear plastic shroud, close the cover to the electronics console and reconnect the main power.

The RS485 serial interface is now ready for multi-point operation.

IMPORTANT:

The installed version of the Model DF868 software must be Version F2Z or higher to support RS485

operation. If necessary, contact the factory for information about a software upgrade.

Table 40: Switch Assembly Settings

Position #

Point-To-Point

Multi-Point

OFF

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 100 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: